Two-piece bolted pipe hanger with a 7/16" clearance hole for hardware mounting. Available in galvanized and stainless steel, sizes 3"-24".

Two-piece bolted pipe hanger with a 7/16" clearance hole for hardware mounting. Available in galvanized and stainless steel, sizes 3"-24".

Two-piece bolted pipe hanger for standard duct support. Available in galvanized, stainless, or carbon steel, sizes 3"-40".

Two-piece bolted pipe hanger for standard duct support. Available in galvanized, stainless, or carbon steel, sizes 3"-40".

15 ft cable hanger kit, the most common hanging method for QF duct due to its ease of use. Material: Galvanized Steel Sized by weight capacity from up to 22 lbs...

15 ft cable hanger kit, the most common hanging method for QF duct due to its ease of use. Material: Galvanized Steel Sized by weight capacity from up to 22 lbs...

Strut-channel mount hanger, tested by MET Laboratories to hold up to 170 lbs at 9" and up to 850 lbs at 20" without failure. Nut and bolt included; strut channel...

Strut-channel mount hanger, tested by MET Laboratories to hold up to 170 lbs at 9" and up to 850 lbs at 20" without failure. Nut and bolt included; strut channel...

Small saddle-style tap used to cut into an existing duct line to begin or extend a QF system. Available in galvanized and stainless steel, sizes 3"-40".

Small saddle-style tap used to cut into an existing duct line to begin or extend a QF system. Available in galvanized and stainless steel, sizes 3"-40".

Saddle-style branch used to cut into an existing duct line to begin or extend a QF system, at 30° (45° optional). Available in galvanized and stainless steel, sizes 3"-40".

Saddle-style branch used to cut into an existing duct line to begin or extend a QF system, at 30° (45° optional). Available in galvanized and stainless steel, sizes 3"-40".

<p>Straight-through tee branch with a 90° side outlet. Both main-line ends must match diameter; the side outlet can be equal to or smaller than the main line. Available in galvanized...

<p>Straight-through tee branch with a 90° side outlet. Both main-line ends must match diameter; the side outlet can be equal to or smaller than the main line. Available in galvanized...

<p>Double-branch fitting for splitting a duct line into three ports (one main plus two branches) at 30° (45° optional). Available in galvanized and stainless steel, sizes 3"-40".</p>

<p>Double-branch fitting for splitting a duct line into three ports (one main plus two branches) at 30° (45° optional). Available in galvanized and stainless steel, sizes 3"-40".</p>

<p>Standard branch fitting for splitting or joining a duct line at 30° (45° optional). Length and reducer needs depend on the port diameters ordered. Available in galvanized and stainless steel,...

<p>Standard branch fitting for splitting or joining a duct line at 30° (45° optional). Length and reducer needs depend on the port diameters ordered. Available in galvanized and stainless steel,...

<p>Symmetrical Y-shaped branch for splitting a duct line into two equal legs at 60° (90° optional). Both branch legs must be at least 50% of the main diameter. Available in...

<p>Symmetrical Y-shaped branch for splitting a duct line into two equal legs at 60° (90° optional). Both branch legs must be at least 50% of the main diameter. Available in...

End cap closes off a QF tap for future use. Optional birdscreen version adds a wire mesh guard. Available in galvanized and stainless steel, sizes 3"-24".

End cap closes off a QF tap for future use. Optional birdscreen version adds a wire mesh guard. Available in galvanized and stainless steel, sizes 3"-24".

<p>Transitions rectangular or square ductwork down to a round QF connection, or square to square, sized to your dimensions. Custom lengths and flange options available. Available in galvanized and stainless...

<p>Transitions rectangular or square ductwork down to a round QF connection, or square to square, sized to your dimensions. Custom lengths and flange options available. Available in galvanized and stainless...

Adapts a QF end to connect with rubber hose. Not compatible with metal flex hose. Available in galvanized and stainless steel, sizes 3"-24".

Adapts a QF end to connect with rubber hose. Not compatible with metal flex hose. Available in galvanized and stainless steel, sizes 3"-24".

dapts a QF end down to a raw ID/OD end for connecting directly to machine ports, with the option to expand up to 0.3" over nominal size. Available in galvanized...

dapts a QF end down to a raw ID/OD end for connecting directly to machine ports, with the option to expand up to 0.3" over nominal size. Available in galvanized...

Adapts duct with QF ends to duct with flanged ends. Angle flange is rotational for easier installation; flat flange available with custom hole pattern. Available in galvanized and stainless steel,...

Adapts duct with QF ends to duct with flanged ends. Angle flange is rotational for easier installation; flat flange available with custom hole pattern. Available in galvanized and stainless steel,...